If you have ever worked with PVC (plastic) primer and cement, you know how difficult they can be to deal with. So, how to glue PVC pipe without primer?
Due to the airtight connection they make, they are also particularly beneficial for joining PVC pipes. Gluecare will provide you with the procedure for bonding plastic pipes without using a primer.
Here are the steps to glue PVC pipe without primer:
- Cut the pipes
- Deburr the inside and outside
- Mark the tube and fittings
- Insert the O-rings
- Tighten the junction
Let’s read on to know more details!
How To Glue PVC Pipe Without Primer?
These connections also referred to as push-to-connect attachments, are particularly ideal for this application. They have a metal ring that bolts onto the attached plastic pipe and a rubber O-ring for watertight.
What You Will Need?
- Sandpaper
- Handsaw or electric saw
- Metal rings O-rubber rings
- Lubricant
- A shove
Step By Step Guideline
You can rely on the following steps to better understand how to glue PVC pipes without using primer or glue.
Step 1: Cut The Pipes
- By screwing pieces of 2×4 together, you may make an alternative pipe.
- Cut the plastic tubes to your intended lengths using a saw with a 4-inch or 5-inch broad blade.
- Note that the square ends fit tightly into the fittings, providing ample contact area for the O-rings to function. They also make the inside surface flatter, allowing for improved water movement.
- If you perform many plumbing repairs, investing in special saws for slicing plastic pipes is a good idea. Most hardware stores have them in the piping tool section or near the handsaws. A sharp blade saw, on the other hand, will suffice.
Step 2: Deburr The Inside And Outside
Using 80-Grit Sandpaper To Smooth The Inside And Outside.
- To fit the shape of the pipe, twist a quarter piece of 80-grit sandpaper into a tube and smooth it gently.
- Using the sandpaper, remove the internal burrs.
- Sand the pipe from the inside and the outside. It would be best if you used sandpaper at an angle until the edges are slightly beveled.
- Burrs can catch hair and debris, producing blockages if left intact.
- Remove burrs using a pocket knife or file, but sandpaper is more convenient and practical.
- Using sandpaper, remove the exterior burrs.
- Note that the pipe will slide into the connection more efficiently, resulting in a tighter fit.
Step 3: Mark The Tube And Fittings
- Dry and fit the pipe connections fitting, aligning the fitting with a level if necessary.
- Make a mark on the pipe and fitting.
Step 4: Insert The O-Rubber Rings
- Clean the rings with a toothbrush, paying particular attention to a ring groove. If possible, avoid using a lubricant-soaked cloth.
- When changing O-rubber rings, remember to clean and dry the ring and the groove before inserting the new O-ring.
- Slide your finger along the lead-in angles of the rubber ring to make sure it is firmly installed, not deformed, and evenly dispersed throughout the groove.
- Put the spigot end of the pipe to the mark with lubricant. Ascertain that all burrs have vanished.
- Level the spigot with the socket and push it into place with a hard, steady shove. To keep previously linked pipes from shutting, reinforce the socket end of the line.
- Ensure the mark is barely visible to the human eye upon that joint. It would be best if you never put a pipe as far as feasible into the socket. It will allow for future pipe expansion.
- If a pipe junction has been settled too far, you can remove it right away. However, once the lubrication has been withdrawn, mechanical assistance is needed to separate the connection.
Step 5: Tighten The Junction
The Result Should Be Like This
- The tube should be slid into the transition connection.
- Fasten the bands and tighten the junction by turning the screws clockwise using a nut driver.
FAQs
Here are some frequently asked questions we have collected while researching this field. They will help you understand in more detail.
Is Primer Necessary For Plastic Pipe?
Some people may tell you that primer isn’t necessary for robust plastic joints. While you can make total joints without primer, it is essential to ensure that your joints are as strong as possible.
On any connections that have liquid substance traveling through them, we suggest using primer.
Is PVC Primer The Same As Glue?
PVC cement has the same active component as tetrahydrofuran primer. Primer eliminates the glossy, protective second coat on PVC.
This ability reveals a “raw” matte texture that aids in glue bonding and aids in the molecular bonding process.
Do I Need To Let The PVC Primer Dry Before The Cement?
No, PVC primer doesn’t have to ‘dry’ before use. It has to be wet to perform its work and not obstruct the cement. Remember that plumbers in a rush use this every day and are not waiting for it to dry before they can grab the cement.
What Is The Best PVC Glue?
The Oatey Glue is another excellent option for the best PVC glue. It is extremely tough, and you can apply it to all PVC pipe schedules and classifications.
If you’re an expert in the field and require a strong adhesive for dealing with PVC, it is one of the most well-known brands.
Is There Another Way To Connect PVC Pipe Without Using Glue?
PVC must be ideal in pipework, holes, seams, and joints. Silicone is an easy and quick way of gluing PVC pipe without primer. However, the tube must be thoroughly dry before adding the silicone.
If you do not adequately seal the plastic pipe, it will not be watertight, allowing water to flow in. Purchase plenty of tubing and design the tube ahead of time to make it watertight.
Conclusion
The above article has provided you with detailed instructions on the method to glue PVC pipe without primer. Hopefully, you have gained more useful knowledge from our sharing. Thank you for reading!
Related post: