How To Glue Wood To Concrete Without Drilling?

Knowing how to glue wood to concrete without drilling holes in it can be crucial to the success of a DIY job. It is a helpful item to have, whether you handle vast and minor projects.

The Epoxy method includes the following steps:

  • Clean the surfaces
  • Make the bead stream
  • Put the Epoxy
  • Support the wood while drying

Gluecare will provide you with various strategies for attaching wood to solid material without drilling, which is ideal to use in your home renovation project.

Let’s read on to know more details!

How To Glue Wood To Concrete Floor Or Wall?

Things You Will Need

  • Mask
  • Gloves
  • Air-powered nail gun
  • Cloth
  • Epoxy glue systems
  • Anchors
  • Glue Applicator
  • Nails
  • Concrete screws
  • Hammer drill
  • Construction adhesive

Step-By-Step Guidelines

It may be a vital aspect of construction if you understand how to attach wood to concrete blocks using Epoxy correctly.

Epoxy glue systems are a systematic approach to fasten wooden things to concrete without drilling. This glue appears primarily to address these issues.

Step 1:

Clean And Dry The Wood

Before using this procedure, you must properly clean and dry the wood to ensure proper bonding. Ensure that all dust, oil, and filth are removed from the sprayer guns with solid injectors on the ends.

Step 2:

Cut The End To The Same Size As The Bead Stream

Make the bead stream:

  • Trim the pump end to the same size as the bead stream.
  • Raise it and force the air out of the chambers.
  • Put the glue to the regions that need to be glued together in vertical, thin stripes.

Step 3:

Use A Razor Knife To Peel The Excess Adhesive Off

Use A Razor Knife To Peel The Excess Adhesive Off

Put the epoxy to the concrete and wood surfaces on a level surface. Then push them securely together and wash away the excess adhesive with a bit of cloth, or use a razor knife to peel it off if it solidifies.

Step 4:

The drying period for this is three days. Still, you should double-check the manufacturer’s safety directions and support the wood solidly in place after applying until the glue has dried.

Pro Tips: You should rely on the instructions in this video to better understand how to do so.


Can I Use Construction Adhesive To Attach Wood To Concrete?

You can use construction glue to properly bond both softwood and hardwood. This type of adhesive accommodates a wide range of wood thermal expansion coefficients, allowing for slight movement with the wood.

Usually, you may attach wood without any support, but it needs interim help if it starts to move. Despite this, the use of glue to secure connections to solid material is daily.

Pressure glue for light items, resins, acrylic spray for various purposes, and polyurethane glue are among the types. Glue bonding requires good wetting qualities, which means the adhesion should spread throughout the surface rather than just bead on it.

The potential to flow into the substantial gaps is required to generate a sufficiently mechanical locking to the layer. The surface must be tidy and have a firm coating.

Are There Other Methods To Glue Wood To Solid Material?

Here are other approaches to attach these components; however, the screw and nail procedure may require drilling.

#1. Use Screws

These ‘tapcon’ fasteners give a quick, simple, and sturdy solution to secure concrete to wood. It does not necessitate the use of hammers or the placement of an anchor or shield.

They have high-low threads that grip close to the sidewalls of the holes and resemble wood screws. These are available in 1/4-inch and 3/16-inch diameter lengths with a depth of 3 3/4 inches.

#2. Use Nails


Nails made exclusively for nailing wood into the concrete are readily available. Seek nails that will go into the solid wall to a depth of approximately an inch, then hammer them in with a sledge.

The shaft has striations around it to boost gripping power, and the steel is toughened so it will not bend when it strikes the concrete. These are inexpensive, durable, and tough to remove.

Ensure the nail is flat during hammering. You may also use a nail gun, but it is risky if you aren’t familiar with it or fragile concrete and liable to shatter when applying pressure.

Screws can also be ideal for this purpose. However, remember that if you use screws or nails, you’ll be drilling holes in the concrete.

#3. Cut Nail

Cut nails are a simple way to fasten wooden objects to the solid surface, similar to nailing timber to hardwood without employing a hammer drill. The cut nail has a tapered, square form.

These nails are inexpensive, hold well since they penetrate at a minimum of 3/4 inch into the concrete, and are exceedingly difficult to remove. They also need a strong shear capacity of up to 600 pounds, as well as precise hammering.

Are There Any Issues When Glueing Wood To Concrete Without Drilling?

Fracture Concrete

If you opt for the nailing method, one issue is the formation of fractures on the surface. This issue appears partly by striking the nail at an incorrect angle or attempting to nail it into concrete at an angle.

But, it is more probable that you’re not hammering the nail firmly enough. That’s why having an air-powered nail gun is an excellent option, as it will blast the nail in rapidly and with a lower likelihood of cracking the solid surface.

However, if the board has a slight curve, likely, the glue will not hold, and it may come off. You have two options for dealing with this.

You may either use a superior adhesive designed for gluing concrete to hardwood or split it into fragments and bond them together.

If the issue is that the board’s weight is pushing it out of position before it has dried completely, this last alternative is ideal.


We hope after reading this article, you can better understand how to attach wood to concrete without drilling. If you have any questions about this, please visit us at Gluecare. Thank you for reading!

Leave a Comment