It is a difficult task to remove gorilla glue from rubber. It can be very frustrating and time-consuming to remove it. But, with the right methods and patience, you can remove the adhesive without damaging your surfaces or having to replace them. In this article, we will go through the 5 most effective ways to remove gorilla glue from rubber objects.
Methods to remove gorilla glue from rubber objects
1. Using Paint scraper or razor blade
Using a paint scraper or a razor blade is the quickest and simplest method to remove gorilla glue from rubber objects.
- To use this method, scrape off as much of the adhesive as possible with these tools, along with some elbow grease.
- If you can see where it has seeped into nooks and crannies, use an old toothbrush to remove it.
This method is effective when you need to remove gorilla glue from rubber objects that don’t have too much adhesive on them.
2. Acetone
Acetone is one of the most chemical solvents that can remove gorilla glue from rubber.
You should always wear gloves and goggles when using this method to protect yourself while you remove the adhesive.
- Apply acetone directly onto the area where there’s a lot of adhesive
- Leave it for half an hour or so
- Wipe away with a paper towel or a piece of cloth.
- If there’s still quite a bit left, apply the acetone again and remove it with an old toothbrush to get rid of any residual adhesive.
Note: If you have sensitive skin, make sure that when you remove gorilla glue from rubber objects using this method that you don’t touch it
3. Cooking oil
- Add a little bit of cooking oil to remove gorilla glue from rubber.
- Then remove it with an old toothbrush.
This method is effective because cooking oil acts as a solvent, breaking down the adhesive and making it easier to remove from surfaces.
Note:
- It’s also important that you make sure you remove all of the leftover residues after using this method or else your object will be sticky again once it dries
- Make sure that the adhesive is in liquid state before trying this method out because if it’s in solid form, it won’t work.
This will remove the majority of the adhesive when you rub it onto your surface with a paper towel or cloth.
4. Mineral spirits
This is another chemical solvent that can remove gorilla glue from rubber objects.
It works best if you have a lot of adhesive on your surface because it’ll seep into every nook and cranny, loosening up all of the dried-up glue inside to remove it easily.
How to use it?
- First, remove as much of the glue from your surface as you can with a scraper or razor blade.
- Once that’s done, pour mineral spirits over it and let it sit for an hour or so.
- Wipe off any remaining residue using paper towels or cloths afterwards.
Again, this method is effective because mineral spirits act as a solvent, breaking down the adhesive and making it easier to remove.
Note:
- If you have sensitive skin, make sure that when you remove gorilla glue from rubber objects using this method that you don’t touch it because mineral spirits are toxic if they come into contact with your skin or eyes.
- If there’s still quite a bit of leftover residue after using one of these methods, there’s another step you can take- sanding down your surface until all remnants of the glue are completely gone.
This will work best for surfaces where the gorilla glue has seeped in deep so be careful before attempting this on any other type of object since it could damage them severely! Just like most things in life, patience really is a virtue when it comes to removing gorilla glue from rubber.
See more: Clean with Mineral Spirits
5. WD-40
WD-40 is a lubricant that helps remove gorilla glue from rubber objects.
- First, remove as much of the adhesive you can by using a razor blade or paint scraper and some elbow grease.
- Then spray the WD-40 over it on your surface
- Wipe away with an old cloth/paper towel afterwards to remove any leftover residue.
This method is effective because of how quickly WD-40 works in breaking down adhesives so if there’s quite a bit of dried-up glue left on your object after trying out one of these methods, this will be able to remove most if not all of it easily!
Also again, make sure that when you try this method out for removing gorilla glue from rubber objects, don’t touch it because WD-40 is harmful if you get it in your eyes or on your skin.
Note:
If the glue has seeped into deep crevices, remove as much of them before attempting this method since it’ll be more difficult to remove leftovers without sanding down the surface itself which could damage it severely!
See How to remove super glue using WD40
Conclusion
Just like most things in life, patience really is a virtue when trying to remove gorilla glue from rubber objects so don’t rush through these steps until all remnants are gone completely.
So be patient, remove as much of the adhesive you can while using one of these methods first and then wait- your object will become clean again in no time!
I hope with the help from this post, you will successfully get rid of gorilla glue from rubber. Even though it works or not, don’t forget to share the result with us by commenting down below.
Thanks for reading and good luck!
Related articles
- Remove Gorilla Glue From Nails: 9 Effective Ways
- 6 Steps to Remove Gorilla Glue From Laminate Floor
- 7 Ways to Remove Gorilla Glue From Ceramic
- 6 Best Methods to Remove Gorilla Glue From Glasses Lens
Frequently Asked Questions
Will Goo Gone remove Gorilla glue?
Yes. Goo Gone is the #1 name in adhesive removers, and it’ll react with any of them.
For outdoor glue removal, use Goo Gone Outdoor Removal Formula to remove stubborn adhesives quickly and find your favorite outdoor surfaces intact. A water-based solution that’s safe for both indoor and outdoor use, this formula has a special quick-drying action that leaves behind no residue or dulling film on hard surfaces like patios or decks. And its non-toxic ingredients are also safe for children and pets who may come into contact with areas where it’s used.
Will vinegar remove Gorilla Glue?
Unfortunately, we cannot answer that question with certainty.
A better question is whether Acetic Acid will work to break down the proteins in Gorilla glue. Vinegar typically has higher acidity than most cleaners but it would be hard for any solvent, including vinegar, to do something that is not already accomplished by the more concentrated acid cleaner. As such, our advice would be to use a more concentrated cleaning agent normally found in stores.
What is the best adhesive remover?
There are two broad types of adhesive removers: hazing and solvents. Hazing removers work by forming a chemical bond with the resin on the surface of the sticker that pulls it away from, or out of, our vehicle’s surface. Solvents work by soaking into and loosening the glue before wiping it off the adhesive tape (and, consequently, our vehicle).
To determine which is best for you it’s necessary to know what kind of residue will be left behind after removal.
However, we can recommend Goo Gone. It’s the only adhesive remover that works on any type of gooey, gunky mess. In fact, this product even removes Scotch tape!
Goo Gone easily adheres to just about any surface and doesn’t leave a sticky residue when removed from clothing or other porous materials. This really grip-friendly formula can be applied with a soft cloth or sponge, then wiped off without rubbing too hard for great indoor and outdoor use!
How do you remove hardened Gorilla Glue?
Gorilla Glue is a two-part epoxy cement that bonds to most surfaces. To remove Gorilla Glue from floors, you must do the following:
1) Clean the surface with an appropriate solvent to dissolve the adhesive
2) Sand off any remaining residue.
Since Gorilla Glue is a two-part epoxy cement, if you use vinyl flooring glue then there will be no need for sanding due to the polyvinyl chloride in dissolves in acetone.
For an outdoor application, follow these steps in reverse order because once Gorilla Glue cures in sunlight or UV light it is irreparable without specialized equipment.
I bought Goo Gone and the first thing it says on the bottle is “do not use on rubber”! SO why are you saying Goo-Gone is the best product to use on rubber to remove glue?